Skip to content
IJZIsaac Johan Ziebarth

Personal project · 2026

OSIRIS flight computer

0 ERC errors

My own flight computer design, kept apart from UQ Space's boards as a learning project. The first board, V0, is a 4-layer bench model whose schematic passes KiCad's electrical rules check (ERC) with 0 errors. Its design rules check (DRC) still flags one short, a power track over a ground pad, which the next revision fixes.

My role
Sole designer
When
May 2026 – present
Tools
KiCad, STM32F411, ISM330IS, BMP581, INA228
Code
Private repository for now

The full write-up

  1. Meet the board
  2. The problem
  3. What I built
  4. Specifications
  5. Result
  6. What went wrong
  7. What's next

Meet the board

Point at a part, or tab through the list, to find it on V0. Number 7 sits on the underside.

Top view of the OSIRIS V0 board with numbered markers on its main parts
  1. 1IMUISM330IS six-axis IMU
  2. 2BarometerBMP581 pressure sensor
  3. 3Power monitorINA228 current and voltage monitor
  4. 43.3 V buckTPS54302 regulator with a 4.7 µH inductor
  5. 5Battery inputXT30, 2S to 4S, behind a fuse, a TVS diode and a reverse-polarity FET
  6. 6Module socketsTwo 20-pin rows for the plug-in STM32F411 module
  7. 7microSDHirose socket on the underside

The problem

I wanted to learn flight computer design from the ground up, on a board of my own.

What I built

  • V0 is a 63 × 74 mm, 4-layer carrier board I designed in KiCad. It takes a plug-in STM32F411 module.
  • The board carries an ISM330IS IMU, a BMP581 barometer, an INA228 power monitor, a 3.3 V buck regulator and a microSD socket.
  • A fuse, a TVS diode and a reverse-polarity FET protect the 2S to 4S battery input.
  • The second board is a larger design around a bare STM32H743, with GNSS, Ethernet, 4 pyro channels and an eFuse.

Specifications

Board63 × 74 mm, 4 layers (V0)
ControllerPlug-in STM32F411 module
SensorsISM330IS IMU, BMP581 barometer
PowerINA228 monitor, 3.3 V buck, 2S–4S input with fuse, TVS and reverse-polarity FET
StoragemicroSD
Parts70 placed: 52 on top, 18 underneath

The interactive bill of materials needs a wider screen than a phone. Open it full size (opens in a new tab)

Interactive bill of materials (BoM) for V0, generated with my eng-tools kit: hover or click a row to light that part on the board, front and back. 70 parts on 45 BoM lines. Open it full size (opens in a new tab)
V0's KiCad files, the board and its six schematic sheets, opened in your browser with KiCanvas. Open the board or the schematic to pan, zoom and select parts and nets. The viewer and the files load only when you open one.

Result

The second board's schematic passes ERC as well; its routing is unfinished.

What went wrong

A design review found that the USB and battery supplies could fight each other on V0. I work around it with a bench rule for now, and the fix is planned for the next revision.

The layout check also flags a short: a 0.8 mm VSYS track on the top layer runs over the ground pad of capacitor C7. I missed it when I first claimed the board was clean.

What's next

  • The next revision separates the USB and battery supplies properly.
  • The VSYS track moves off C7, so the layout check passes too.
  • I have not written firmware for either board yet.